Analog Data Acquisition System,Data Loggers System,Digital Data Acquisition System,Digital Data Loggers,India

Data Loggers & Data Acquisition System

Dcon / Modbus Serial RS485 Analog & Digital I/O Modules

I 7017 Input Type		+/-150mV, +/-500mV , +/-1V, +/-5V, +/-10V +/-20mA (requires optional external 125 ohm resistor)
I 7018 Input Type		+/-15mV, +/-50mV, +/-100mV, +/-500mV, +/-1V, +/-2.5V +/-20mA (requires optional external 125 ohm resistor) Thermocouple Type J, K, T, E, R, S, B, N, C
I 7013/33/15 Input Type		RTD ( 1/3/6 channel)
Wire connection		2/3/4 wire
RTD Type		Pt100 a=0.00385, Pt100 a=0.003916, Ni120, Pt1000 a=0.00385
I 7016		2 ch strain guage input
Input Type		+/-15mV, +/-50mV, +/-100mV,+/- 500mV , +/-1V,+/- 2.5V, +/- 20mA
Output Channels		1
Output Range		0 to +10V
Max Output Load		40mA
Accuracy		+/-0.05% of FSR
Drift		+/-50ppm/ °C
Output Impedance		12 Ohms
Isolation		3000 VDC
I 7021/22/24 Analog Data Acquisition system Output		1/2/4 channel
Output Type		0~20mA, 4~20mA, 0~5V, +/-5V, 0~10V, +/-10V
Resolution		14-bit
I 7041/51/52/52		14 / 16/ 8
Input Type		Sink or Source,Isolated channel with common power or ground
I 7042/43/45		13/16
Output Type		Isolation Open Collector
Output Voltage		30V max.
Output Current		100mA per channel, Direct drive power relay module
Isolation Voltage		3750V
I 7058/59 AC INPUT Module		8
Input Type		AC, Differential, isolated
Off Voltage Level		30VAC max.
On Voltage Level		80 ~ 250VAC
AC Frequency		50~60Hz ( > 45Hz Min.)
Channels		7
I 7044/50/55D Digital I/O MODULE		Source, non-isolated channel with common ground
Off Voltage Level		+1V max.
On Voltage Level		+4V ~ +30V
Input Impedance		3K9, 0.3W
Counters		channels : 7
		Max. Counters : 16-bit (65535)
		Max. Input Frequency : 100Hz
		Min. Pulse Width : 5ms
Digital Data Acquisition system Output :
I 7044/50/55D Digital I/O MODULE		8
Output Type		NPN, Source, Open collector
Output Voltage		30V max.
Output Current		30mA max.
I 7080/83 COUNTER I/O MODULE		COUNTER / 3-axis
Input Type		Isolated
Encoder Mode		Quadrant counting mode, CW/CCW counting mode, Pulse/Dir counting mode
Isolation Voltage	Input level 5V	Logic High : 3.5V~5V
		Logic Low :0V~2V
		Logic High: 5V~12V
	Input 12V with external resistor 1K ohm	Logic Low :0V~2V
	Input 24V with external resistor 2K ohm	Logic High:7V~24V
		Logic Low :0V~2V
Maximum Count	32bit
Maximum counting rate	1MHz

request a quote

Analog Input
Input Channels	1/ 8 differential or 6 differential and 2 single-ended by jumper select
Input Type	+/-15mV, +/-50mV, +/-100mV,+/- 500mV , +/-1V,+/- 2.5V, +/- 20mA
Resolution	16-bit
Sampling Rate	10 Samples/ Second
Accuracy	+/-0.1%
Band Width	15.7 Hz
Zero Drift	0.5uV/°C
Span Drift	25ppm/¢XC
Input Impedance	20M Ohms
Common Mode Rejection	150dB
Normal Mode Rejection	100dB
Over Voltage Protection	+/-35V
Open Thermocouple Detection	No
Photo-Isolation	3750 Vrms
Intra-module Isolation, Field to Logic	3000 VDC
Interface
Interface	RS-485
Format	N, 8, 1
Buad Rate	1200 ~ 115200bps
LED Display
1 LED as Power/ Communication indicator
Power
Input	+10 to +30 Vdc
Power Consumption	1.0W
Environment
Operating temperature	-25 to 75¢XC
Storage temperature	-40 to 85¢XC
Humidity	5 to 95%, non-condensing
Note: Above is common specification

Modbus Analog / Digital I/O

Type		Model		Description
Analog Input	Voltage & Current(Selection Guide)	M-7017	M-7017RC	Measure V, mV, mA
		M-7017C	M-7017R-A5
		M-7017R	M-7017Z
	Thermocouple(Selection Guide)	M-7011	M-7018R
		M-7011D	M-7018Z
	RTD(Selection Guide	M-7018	M-7019R
		M-7015	M-7015P
		M-7033	M-7033D	Measure V, mV, mA, temperature (With thermocouple sensor)
	Thermistor(Selection Guide)	M-7005		Measure temperature with RTD sensor
	Strain Gauge(Selection Guide)	M-7016	M-7016D	Measure temperature with thermistor
				Measure strain

Type		Model		Description
Analog Data Acquisition system Output(Selection Guide)		M-7022	M-7024	Slew rate of AO channels are programmable
Type		Model		Description
DC Digital Input(Selection Guide)		M-7041	M-7052	DI channels can be used to get status and low speed (100Hz Max.) counts
		M-7041D
		M-7051	M-7052D
		M-7051D	M-7053
			M-7053D
DC Digital Data Acquisition system Output(Selection Guide)		M-7045	M-7045D	DC Output Module
DC Digital Input and Output(Selection Guide)		M-7050	M-7055	DI channels can be used to get status and low speed (100Hz Max.) counts
		M-7050D	M-7055D
Type		Model		Description
Power Relay Output(Selection Guide)		M-7060	M-7060D	Traditional Relay; Approx life-time:Mechanical: 20x10^6 OPSElectrical: 100x10^3 OPS Full Load
		M-7065	M-7065D
		M-7067	M-7067D
Type		Model		Description
Counter/Frequency(Selection Guide)		M-7080	M-7080D	Input signal range can be 1Hz to 100KHz
		M-7080B	M-7080BD

request a quote

Programmable Datalogger SERS 951-D

1/4 DIN size package.
Microprocessor based accuracy.
Alarm capabilities with relay outputs.
8 ch, 16 ch, or 24 channel models.
AUTO / MANUAL mode facilities.
Addressable serial interface.
Retain set up during power loss.
Data storage for analysis using standard 80 columns printer.
Lower cost of ownership. Universal input, can be selected on site.
Memory available 8K, 16K & 32K.
Alarm relay board for 8 ch,16 ch,24 ch available.
Multidrop RS 485 connectivity.
Size: 96 x 96 x 120 mm.

PRODUCT RANGE